Foxmere Technologies

COVID-19: Business as usual.
COVID-19: Open as usual and still supporting manufacturers globally.

FX, A and Q Series PLC Level 1


Course Outline

Upon completion of the course the student should:

  • Be able to recognise Mitsubishi FX, A and Q Series hardware and be able to locate and cure most faults that occur.
  • Be able to operate the GX Developer software to make it perform certain tasks.
  • Understand basic FX, A and Q Series instruction set and be able to make minor modifications to software.
  • Be able to backup and restore a PLC program when required.
  • Be able to perform basic system diagnostics when a problem occurs.

Download PDF

Equipment per Delegate

  • Mitsubishi FX, A or Q Series PLC.
  • PC or laptop.
  • Simulator.

Course Content

To fault find a system you need to know exactly how it works.

How exactly does a PLC work?

  • Am I getting the input to the PLC?
  • The LED on the output card means I am getting voltage out right?
  • What exactly happens in-between? Theres more than just a program in the CPU.
  • How exactly does it scan the program?
  • What is this Watchdog Timer? Is it that important?
  • Can I use the same output twice? That's bad programming isn't it?
  • A PLC is a logic controller, so use a logical approach to fault find it.
  • What are the 8 simple test points to check?
  • What is the difference between forcing and toggling?

How do I do the following?

  • How do I check the power is ON and the PLC is in the right mode (RUN or Program).
  • Check for a fault condition.
  • Establish a link between PC and PLC.
  • If comms problem check interface.
  • Create a blank project and take a backup.
  • Open project for PLC and go online.
  • Interrogate diagnostics.
  • Identify a hardware / software fault.
  • Change the battery.
  • Change modules if necessary (with and without spares).
  • Identify a PLC or comms fault.
  • Check all settings against a template, etc.
  • Check hardware (what voltage should be where).
  • Clear memory and download program.
  • Check software against latest copy.
  • Monitor program effectively.
  • Searching for specific operands and instructions.
  • Changing timer, counter values online.
  • Making minor modifications online and offline.
  • Check or create a monitor table to establish parameter status.
  • Force a parameter if required.
  • Call up reference data to assist with software diagnostics.
  • Display documentation (symbols, comments).
  • Reassign an IO address and change software addresses.
  • Printing cross reference / program listings, etc.
  • Ethernet communications.
  • Analogs and scaling.
  • Higher level instructions.

Background information also covered.

Understanding the following

  • Number formats, bits, bytes, words, double words.
  • Binary, HEX, octal, floating point, integer.
  • Data types and parameter types, bool, etc.
  • Online and offline modes.
  • Basic instructions, contacts, set, reset, etc.
  • Timers and counters.
  • Comparators, maths.
  • How to make minor modifications.
  • Altering values in a monitor table.
  • Using device monitor function.
  • Using force function.
  • Back tracking through a program to establish where power flow stops.
  • Reset procedure.
  • Fault finding tips.


Provisional bookings can be made via email, phone or letter. Confirmation in writing with a purchase order number is required four weeks prior to the course start date.

Dates may be offered to other customers after this date.

Joining instructions are sent out approximately two weeks prior to the course start date.

Book Now

Course Times

Typical course times are 09:00 to 16:30. Alternative arrangements can be made for customised and on-site courses.


A light lunch will be provided when training at our in-house facility.

Payment and Cancellations

Fees are based upon payment being made to confirm course booking. Should you be unable to meet these terms please advise us as we will be able to re-quote on your payment terms.

Prices are quoted exclusive of VAT. New Customers are required to pay pro forma.

Requests for cancellation must be made via email or letter. Cancellation charges may apply.

Course Specifics


Mitsubishi FX, A or Q Series


GX Developer


5 days

Max. Delegates



Fill out this form to get availability, pricing and additional details for this course.